Face finish: The finish on the face of flange is measured as an Arithmetical Average Roughness Height(AARH). The finish is determined by the standard used. For example, ANSI B16.5 specifies face finishes within a range 125AARH-500AARH(3.2Ra to 12.5Ra). Other finishes are available on requst, for example 1.6 Ra max,1.6/3.2 Ra, 3.2/6.3Ra or 6.3/12.5Ra. The range 3.2/6.3Ra is most common.Product Specification: 1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3.
ติดต่อเดี๋ยวนี้
Blind Flanges. Blind flanges need not be facedin the center if, when this center part is raised, its diameter is at least 25 mm (1 in.) smaller than the inside
diameter of fittings of the corresponding pressure class,
as given in Tables 9 and 12 (Tables II-9 and II-12) or25 mm (1 in.) smaller than the mating pipe inside diameter. 1. Standard:GOST 12820- 80 GOST 12821- 80 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.
ติดต่อเดี๋ยวนี้
Flanges Introduction:A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004. Size1/2"-48"5.
ติดต่อเดี๋ยวนี้
Face finish: The finish on the face of flange is measured as an Arithmetical Average Roughness Height(AARH). The finish is determined by the standard used. For example, ANSI B16.5 specifies face finishes within a range 125AARH-500AARH(3.2Ra to 12.5Ra). Other finishes are available on requst, for example 1.6 Ra max,1.6/3.2 Ra, 3.2/6.3Ra or 6.3/12.5Ra. The range 3.2/6.3Ra is most common.1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007.
ติดต่อเดี๋ยวนี้
Any spot facing or back facing shall not reduce the flange thickness to less than the flange thicknessspecified. When spot facing is used, the diameter shall be large enough to accommodate the outside
diameter of the equivalent normal series of washers in accordance with EN ISO 887 for the bolt size
being fitted. The bearing surfaces for the bolting shall be parallel to the flange face within the limits
given in Table 22. When a flange is back faced a minimum fillet radius, R2 (see Figure 17) in accordance
with Table 23 shall be maintained.1.
ติดต่อเดี๋ยวนี้
1. How can I get a quotation from you ?You can leave us message, and we will reply every message in time. Or we may talk on line by Trademanager.And you can also find our contact information on contact page.1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7.
ติดต่อเดี๋ยวนี้
Flanges Introduction:A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.
ติดต่อเดี๋ยวนี้
It should be noted that this standard does not cover all flange sizes covered by the above DIN Standards.For flange dimensions not specified here, refer to DIN 2501-1. 1. Standard:EN1092-1 2. Type:Type 01 ;Type 02; Type 05; Type11; Type12; Type133. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1.
ติดต่อเดี๋ยวนี้
Flange Material:Carbon SteelFlange Manufacturing Way:ForgedFlange Size:2/1"-48"(DN15-DN1600)1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005.
ติดต่อเดี๋ยวนี้
whereas ISO 7005-1 included in its scope both the original DIN based flanges and also the originalANSI/ASME based flanges, EN 1092-1 contains only the PN based flanges. CEN/TC 74 has produced a separate series of standards, EN 1759-1, EN 1759-3 and EN 1759-4, dealing with the ANSI/ASME based flanges in
their original Class designations;1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.
ติดต่อเดี๋ยวนี้
1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007. PackingWooden Case, Pallet.8.
ติดต่อเดี๋ยวนี้
Surface treatment: Antirust oil, black / yellow / transparent / electric galvanized / hot galvanized1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1.
ติดต่อเดี๋ยวนี้
Class is marked with 6 pressure ratingsThey are: Class 150; Class 300; Class 600; Class 900; Class 1500; Class 2500Product Specification: 1. Standard:ASME B16.5; ASME B 16.47 Series A(MSS SP-44); ASME B 16.47 Series BAWWA C2072. Type:Plate flange, Slip on ,Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:Class 150; Class 300;Class 400;Class 600;Class 900;Class 1500;Class 25004. Size1/2"-48"5. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:A105; A105N7. PackingWooden Case, Pallet.8.
ติดต่อเดี๋ยวนี้
1.Each layer use plastic film and rubber sleeve to protect the surface2.Package by wooden case3.Shipping mark can make on request4.Markings on products can be laser or stamp.OEM is accepte1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9.
ติดต่อเดี๋ยวนี้
Flanges Introduction:A flange is a approach of connecting pipes, valves, pumps and other gear to form a pipework system. It additionally provides handy access for cleaning, inspection or modification. Flanges are typically welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.
ติดต่อเดี๋ยวนี้
The p/T ratings of this standard have been reduced in many cases by either limiting the lowertemperature ratings which can no longer exceed the PN value, or by increasing the rate at which
allowable pressures shall reduce with increase in temperature;2) in addition to the range of PN 2,5 to PN 40 DIN origin flanges contained in the ISO standard,
EN 1092-1 also includes flanges up to PN 400.1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005.
ติดต่อเดี๋ยวนี้
such as oil, chemical industry, water conservancy, electric power, boiler, machinery, metallurgy, sanitary construction etc1. Standard:DIN2502,DIN2503,DIN2527,DIN2566.DIN2573,DIN2576; DIN2633 ; DIN2632; DIN2631;DIN25662. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange.3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9.
ติดต่อเดี๋ยวนี้
Flanges Introduction:A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7.
ติดต่อเดี๋ยวนี้
Flanges Introduction:A flange is a method of connecting pipes, valves, pumps and other equipment to form a pipework system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or crewed into such systems and then joined with bolts.Product Specification:1. Standard:EN1092-1 2. Type:Type 01 ;Type 02; Type 05; Type11; Type12; Type133. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7.
ติดต่อเดี๋ยวนี้
In BS EN 1092-1:2007, the materials and material groups used in the manufacture of flanges are given in Table 9 and their corresponding.Pressure/Temperature ratings are given in Annex G (normative). Additional materials that are widely in used in Europe are listed in Annex D (informative) but BS EN 1092-1:2007 contains no corresponding Pressure/Temperature information for these materials. National Annex NA (informative) contains guidance on Pressure/Temperature ratings for materials S235JR/1.0038 and ASME SA 105, which are predominantly used in the UK.1. Standard:EN1092-1 2.
ติดต่อเดี๋ยวนี้
This Published Document is the UK implementation of EN 1092‑1:2018. Itsupersedes BS EN 1092‑1:2007+A1:2013, which is withdrawn.1. Standard:BS4504 2. Type:Plate flange, Threaded, Irrigation,Blind, Lap Joint flange. Type3. Pressure Class:PN6;PN10; PN16; PN25; PN40; 4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:RST 37.2; P245GH ; S235JR7. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order1. Standard:BS4504 2.
ติดต่อเดี๋ยวนี้
Cnc machining parts,cnc machining, cnc turning, customized bolt, nut, punch, plastic injection.1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007. PackingWooden Case, Pallet.8. Payment:L/C, T/T, Western Union, PayPal9. Delivery time:30 ~60 days after confirm the order
ติดต่อเดี๋ยวนี้
A: We control the quality since Material arrive, we have workshop QC responsible for each producting line to check the product dimensions and other details during one by one producing process, inspection QC do spot check for each batch in everyday and package workers do 100% product appearance inspection one by one when they package the parts into the carton. 1. Standard:JIS B2220 2. Type:SOP; SOH3. Pressure Class:5k;10k;16k;40k4. Dimension:DN10-20005. Surface Treament:Anti-rust oil; Yellow paint; Black paint;Hot dip Galavnised; Zinc.6. Raw Material:SS4007.
ติดต่อเดี๋ยวนี้
flange connections, which are used for two kinds of pipes, fittings, or devices, are first fixed in a flange flange, and between the two flanges, flange pads are bolted together, which completes the connection. Some pipe fittings and equipment have their own flange, also belong to the flange connection. Flange connection is an important connection mode in pipeline construction. Flange connection is easy to use and can withstand greater pressure. Flange connection is widely used in industrial pipeline. In the home, the pipe diameter is small, and is low pressure, not visible flange connection.
ติดต่อเดี๋ยวนี้
